DEVI devireg 550 Manuel d'utilisateur télécharger pdf

Programming your Devireg 550 Thermostat

Operation Factory Pre-set Range

Recommended Floor Maximums

Network Type

Before setting your Devireg 550

You now need to Activate & set your Devireg 550 to your preferred settings.

NB: when connected to the Power supply for the first time, your Devireg 550 defaults to the factory pre-sets and will be display the word CODE.

Adaptive Function

Temp Display

Sensor

Max. Floor Temp

Offset

Savings Set-Back*

Weekday

Time

Timer Settings

MAS (Master) : SLA (Slave)

On (AdAP) : Off (OFF)

Devi recommends a Floor Sensor

ALWAYS be fitted

°C

r S (Room only) : FS (Floor only)

+20°C to +50°C

-5.5°C to +5.5°C

0°C to -30°C

27°C

35°C

27°C

45°C

Tiles on Chipboard

Carpet/Vinyl on Chipboard

Wooden Floors

Other (concrete, FLC)

1 to 7 (eg 1=Mon, 7= Sunday)

24 Hr Clock format

Up to 336 per week

ALO

AdAP

°C

rFS

OFFS

Not set

Alone

Adaptive On

Centigrade

Room & Floor

+ 35°C

0°C

-5°C

Energy Saving Technology. Your Devireg 550 offers an “adaptive” feature. That is, using the built-in

Energy Saving technology. So, when you select the Heating Times you want for your floor (room), set the

time the floor is to be ready for use (at temp) and the time when it’s finished with. e.g. I want my Bathroom

floor hot at 5:30am and I’m finished with it at 7:30am. You set these times. Your Devireg 550 will work out

when to start & stop to ensure your floor is ready at these times. After setting, you may notice that your

Devireg 550 turns ON during a NOT REQUIRED period for a day or so. This is normal as your Devireg 550

works out the heating characteristics of your room.

You may disable this feature if desired and your Devireg 550 will then switch ON or OFF at your set Times

Individual or Networked. Your Devireg 550 can operate by itself (ALONE) or control or be controlled by

another Devireg 550 which means one of your Devireg 550s would be the MASTER, the rest being SLAVES.

Devireg 550’s can also be networked (set & adjusted from your PC). Up to 32 Devireg 550s can be on each

network.

Savings Set-Back - When in a “Not Heating” period, the Devireg 550 does not actually “switch off” as such.

The Thermostat follows the “Savings” Set-Back temperature you select. If the Savings Set-Back temperature

is sufficiently low enough, then to all intents and purposes the Thermostat is “off” – it will not provide heating

until the next scheduled COMFORT Heat period.

Example If you have set your COMFORT heating temperature to 25°C and the LO (SET-BACK or SAVINGS

temp) set to -15°C, then when your Devireg 550 has finished the COMFORT heating period, the heating will

switch off and the temperature will start to fall but in fact not be allowed to go below 10°C in this example

(25°C -15°C). The Devireg 550 will keep the Floor (or Room) at 10°C. Since it is unlikely that the Floor (or

Room) temperature will fall to this level, the Devireg 550 will to all intents and purposes, be “Off”. So you can

see that you can set the thermostat to effectively be “OFF” or to maintain a lower floor (or room) temperature

– in other words, a SAVINGS temperature.

Child-Proof Lock. Your Devireg 550 offers a Child Proof Lock facility

1 2 3

Résumé du contenu

Page 1 - ALWAYS be fitted

Programming your Devireg 550 Thermostat Operation Factory Pre-set RangeRecommended Floor MaximumsNetwork TypeBefore setting your

Page 2 - Child Lock

Please Note: If during the set-up process, a screen selection remains unchanged for 1 minute, the Devireg 550 will exit without storing any changed va

Page 3 - Setting the Temperature

To alter Timer program steps – Re-Enter the above process, select your Day, follow as above and the “old” values will be over-written or “Rubbed out”T